From minor seepage to full basement flooding, JCB Waterproofing and Construction provides engineered solutions that protect your foundation and your investment.
Four reasons why Millington homeowners trust us with their most important asset.
Our interior drain tile systems are sized and sloped to specification, ensuring gravity carries water to your sump pump without clogging or backing up over time.
Block wall seepage is addressed with a combination of core-filling, waterproof parging, and interior membrane systems that stop moisture transfer even under sustained hydrostatic pressure.
We document every installation with before-and-after photos, moisture readings, and a written record so you have evidence of the work performed and its conditions.
Our quotes include the scope of work, materials specified by brand and model, warranty terms, and the payment schedule -- everything you need to compare us fairly.
Hydrostatic pressure is the invisible force behind nearly every basement water problem homeowners face in Millington, TN. When soil around your foundation becomes saturated -- whether from heavy rain, snowmelt, or a high water table -- it exerts outward and downward pressure against concrete walls and floor slabs that can exceed hundreds of pounds per square foot. Over time, this pressure finds the smallest weakness: a tie rod hole, a cold joint between wall and footing, a shrinkage crack in poured concrete, or a deteriorated mortar joint in block construction. Once water finds its path, that path widens with every wet season until a trickle becomes a flood.
Interior drain tile is the most reliable and widely proven basement waterproofing method for existing homes in TN because it manages water that has already entered the wall cavity rather than attempting to stop it at the exterior. The system consists of a perforated pipe, encased in clean washed gravel, installed at or below the footing level in a channel cut along the perimeter of the basement floor. Water that enters the wall-floor joint, seeps through cracks, or migrates through porous concrete flows into this channel and is directed by gravity to a sump basin. A properly sized sump pump then discharges the water away from the foundation. When correctly installed, this system operates indefinitely without clogging because the inlet is protected from sediment by the gravel bed and a filter sock on the pipe.
In poured concrete walls, the most common seepage points are cold joints, tie rod holes, and form tie locations. These are concentrated, well-defined penetrations that respond well to polyurethane or epoxy injection -- a process of drilling small ports along the crack or joint, installing surface-mounted injection ports, and pumping low-viscosity resin under pressure until it fills the void completely. The cured resin is permanently flexible or rigid depending on the product chosen, creating a watertight seal that moves slightly with seasonal concrete expansion without reopening.
Window wells in below-grade basement windows are a frequently overlooked water entry point. When the well fills with rainwater faster than the soil at the bottom can absorb it, that water presses directly against the window frame -- typically the weakest point in the entire basement envelope. We address window wells with a dedicated drain assembly at the base of the well, tied into the interior perimeter drain system, combined with a properly sized and anchored polycarbonate cover that deflects rain while allowing emergency egress.
Our written warranty covers both the installed drainage system and the sump pump equipment against defects in materials and workmanship. We recommend scheduling an annual inspection with our team to check that pump floats are operating freely, the battery backup is holding a charge, and the drain system's outlet is unobstructed. Homeowners in Millington, TN who maintain this schedule rarely experience warranty claims because we catch the small issues before they become large ones.
Six core services covering every source of basement moisture in Millington homes.
We size every drain tile system to the specific hydrology of your basement, ensuring the pipe diameter and sump pump capacity match your worst-case water intrusion load.
Poured concrete wall cracks are permanently sealed with low-viscosity polyurethane resin injected under pressure through surface-mounted ports drilled along the crack length.
We install pedestal and submersible sump pumps from commercial-grade manufacturers and include a battery backup unit as standard on every new installation.
Hollow-core concrete block walls are treated with hydraulic cement parging and crystalline waterproofing compound that bonds into the block face and eliminates surface seepage.
After injection, we verify the repair with a moisture meter reading to confirm that subslab water transmission has been eliminated at the crack location.
We install polycarbonate well covers sized and anchored to each specific well, deflecting direct rainfall while meeting egress requirements and maintaining ventilation.
We measure moisture levels at multiple points, probe for efflorescence sources, and map every water entry location before recommending any solution.
Our quotes include alternatives at different investment levels so you can choose a phased approach if budget requires it.
Our certified crew completes the installation with minimum disruption to your home, working from a phased sequence designed to protect furnishings and maintain basement access throughout.
Your warranty packet includes installation photos, moisture reading logs, and contact information for scheduling future annual inspections.
After three failed attempts with other companies, JCB Waterproofing and Construction finally fixed our basement for good. The drain system has handled two major rainstorms with zero water in the basement.
The quote was detailed, the crew was on time, and the work was exactly as described. They even patched the concrete so neatly you can barely tell there was a drain trench cut.
I called three companies before choosing JCB Waterproofing and Construction. They were the only ones who actually measured the moisture levels and explained what was causing our specific problem before quoting a fix.
Get a written quote from certified professionals who have solved every type of basement water problem in TN.
Call +1-866-476-1348 Now